Jazz Digit 1 Code Reset And Read Backup Done With UMT

Jazz Digit 1 Code Reset And Read Backup Done With UMT

READ BACKUP

Operation : Read Firmware
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM13)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1400900 [8909] 00000000
OPK_DATA : 9CBA94693C2333A562BCF0E0E981C558748817D002F543B2A2 6AB1B4B3F1CF9E
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Loader...Done
Sending Loader [8909_037]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8909, eMMC, 4 GB
LU Count : 1 [0x00748000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
USERDATA : Normal
Reading Device Information...OK
Device : JAZZ Digit1 [msm8909]
Software : JAZZ_Q8905A_1812_V110T_PK, Hipad-msm8909_64_01.00.01RDD [一 3月 26 18:50:53 CST 2018]
Android Ver. : 4.4.4
Patch Level : xxxx-xx-xx
Reading [modem]...Done
Reading [sbl1]...Done
Reading [sbl1bak]...Done
Reading [aboot]...Done
Reading [abootbak]...Done
Reading [rpm]...Done
Reading [rpmbak]...Done
Reading [tz]...Done
Reading [tzbak]...Done
Reading [misc]...Done
Reading [splash]...Done
Reading [sec]...Done
Reading [boot]...Done
Reading [system]...Done
Reading [persist]...Done
Reading [cache]...Done
Reading [recovery]...Done
Reading [userdata]...Done
Reading [gpt_main0]...Done
Reading [gpt_back0]...Done
Saved to : C:\UMTool\QcFire\Read\JAZZ_Digit1_JAZZ_Q8905A_1812 _V110T_PK_xxxx-xx-xx\
Operation Finished.
QcFire Ver. 4.1

RESET CODE

Operation : Format FS
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM13)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1400900 [8909] 00000000
OPK_DATA : 9CBA94693C2333A562BCF0E0E981C558748817D002F543B2A2 6AB1B4B3F1CF9E
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Loader...Done
Sending Loader [8909_037]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8909, eMMC, 4 GB
LU Count : 1 [0x00748000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : JAZZ Digit1 [msm8909]
Software : JAZZ_Q8905A_1812_V110T_PK, Hipad-msm8909_64_01.00.01RDD [一 3月 26 18:50:53 CST 2018]
Android Ver. : 4.4.4
Patch Level : xxxx-xx-xx
Preparing Data...Done
Formatting Userdata...Done
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 4.1