Bug in UMT Qcfire 3.0

after removing mi account of redmi note 3
system partition is missing

2 set dead
after flashing is alive but baseband unknown

mi account remove log first phone

Operation : Reset Mi Account
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM57)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1009B00 [8976] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8976_001]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8976, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Redmi Note 3 [msm8952]
Software : MMB29M, V9.6.2.0.MHOMIFD [Tue Sep 4 21:07:53 CST 2018]
Android Ver. : 6.0.1
Patch Level : 2018-07-01
Resetting Mi Account Data...Done
When phone is completely ON, connect to Internet and add Mi Account.
-------------- INFORMATION --------------
New Firmware may cause hang on logo.
In such case, you need to flash phone to recover.
Or downgrade firmware and try Reset Mi Account again.
Operation Finished.
QcFire Ver. 3.0
QcFire Ver. 3.0


Second note 3 Log


Operation : Reset Mi Account
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM57)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1009B00 [8976] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8976_001]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8976, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Redmi Note 3 [msm8952]
Software : MMB29M, V9.5.3.0.MHOMIFA [Thu Apr 5 21:47:47 CST 2018]
Android Ver. : 6.0.1
Patch Level : 2018-03-01
Resetting Mi Account Data...Done
When phone is completely ON, connect to Internet and add Mi Account.
-------------- INFORMATION --------------
New Firmware may cause hang on logo.
In such case, you need to flash phone to recover.
Or downgrade firmware and try Reset Mi Account again.
Operation Finished.
QcFire Ver. 3.0
QcFire Ver. 3.0


After dead log

Operation : Read Information
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM57)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1009B00 [8976] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8976_001]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8976, eMMC, ERASED GPT
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
SYSTEM partition is missing!
Operation Finished.
QcFire Ver. 3.0

Here is Screen Shots

Attached Images

	note 3.jpg (83.4 KB)
	note 3 system partition missing.jpg (84.9 KB)